Manual Mill Machine Kits

Coolant Kits

Increase production, get finer finishes on more metals, and extend the life of your tools. To keep your workpiece clean, cool and lubricated while you work, the Coolant Pack includes: Electric Coolant Pump Kit, Smithy Cutting & Tapping Fluid, Hose with Magnetic Base, and Premier 450 Synthetic Coolant. Not included: 110v/220v plug - allowing you to either wire it directly to your machine or to wire it to a corresponding plug in your work area.

Boring Head Combo Kit

Accurately bore holes or refinish holes with your mill. The set includes a 2” boring head and a nine-piece carbide-tipped boring bar set. It features three mounting configurations for the 1/2" shank cutting tools to allow you to bore holes from 3/8" - 5"+ in diameter. Some larger diameters will require shaping the carbide cutters and there are some practical limitations. When the cutter is mounted horizontally, the boring head will contact the bottom of a blind hole before the cutter. The head is adjustable in 0.001" increments and has a direct read dial for greater accuracy. The part number for the head only is 47-705. The C6 carbide cutters are brazed on 1/2" shanks with a variety of chip sizes: a minimum hole range is 0.46" - 0.710" depending on the cutter. Maximum hole diameter will vary, again depending on the cutter, how it is positioned in the boring head, and type of hole being cut. The length of the cutters are from 2.250" - 4.570" in length and can vary slightly. The 9-pc set can be ordered separately, part number 47-700. The adapter mount for the boring head is 7/8"-20. Please select the right size shank for the machine. MT3 millheads require shank number 47-720, sold separately. R-8 millheads require shank 47-725, sold separately.

Drawbars

Pull collets and adapters up into your millhead spindle with these drawbars.

V-Belt Kit

Long-lasting quality V-Belt kits are available for the Midas and Granite machines.

The Midas 1220 and 1220 XL (CB-1220 and CB-1220 XL) require a 4 belt set: 1 belt for the mill, 2 belts for low speeds on the lathe, and 1 belt for high speeds on the lathe.

The Midas 1220 LTD (aka GN-1220 XL LTD) require a 5 belt set: 2 belts for the mill, 2 belts for low speeds on the lathe, and 1 belt for high speeds on the lathe.

The Granite Classic or Granite Industrial with 1.5 100 v hp DC motor requires 3 belts and with the idler pulley added, requires 4 belts. If your Granite Classic or standard Granite Industrial 1.5 hp, 220 volt does not have the idler pulley, it is strongly recommended that you add the idler pulley, #40-300G, to your machine. See #40-300g for more information.

The Granite MX, IMX, and ELX (Elite) with the 2.0 hp DC brushless motor, require 3 belts.

Countersink Drills

Drill center holes in the ends of stock before setting up between centers. These self-centering HSS tools have 60-degree angles to match the lathe centers. Kit includes one of each size.

Countersink Drills

Drill center holes in the ends of stock before setting up between centers. These self-centering HSS tools have 60-degree angles to match the lathe centers. Kit includes one of each size.

Carbide Tip Tool Bit 1/2"

Traditional collets only hold the shank of the cutter or tooling. The R8 Quick Change Tooling System incorporates a wider base on the fixture with a recess on the back that allows the fixture to rest on the face of the machine spindle. This wider base gives the tooling greater stability since it references off the spindle taper and the nose of the spindle - enabling the tooling to always return to the same height. The repeatability of the vertical location is critical for use with small CNC machines that use the R8 taper.

Collet holders are available as well as drill chuck arbors and end mill holders. The 3/4" shank tools are a great addition to the gang tool system used on the AutoMate RP GL-1108 lathe as well as other setups that accept the 3/4" shank.

Quick Tool Holder Kit

These collets mount and center tools quickly. Tooling ends have a shaft keyway and flare to center the collet in the quill. Use collets with 7/16” drawbar. Kit includes one of each size - 1/8", 3/16", 1/4", 5/16", 3/8", 1/2", 5/8", and 3/4"

R8 Collet Set

All you need to set up with collets. This 5C Collet Kit is perfect for machinist who demand higher precision. The scrolling 5C Collet Chuck secures the 5C collet in place and allows the operator to easily change out collets. Includes 8 collets (3/16" thru 1"), collet stop, 5C scrolling chuck, chuck key and collet rack. Available for the Granite and Midas series. Listed are all parts included in the kit, available for separate purchase. The only difference between the kits is the different collet chucks that are specific to the Granite or Midas.

5C Collet Kit

Our best milling vise with precision-machined surfaces holds your work securely. Comes complete with 360 degree rotating base, vise, and mounting hardware.* The three-inch vise has jaws 3-3/16” wide and 1” deep with 3” opening. Four-inch has jaws 4” wide and 1-3/8” deep with a 4” opening.

*K99-320 - mounting hardware included will mount the vise to the base and the T-bolts will fit a 5/8" T-slot. If your machine has a 7/16" T-slot (all Granite and Midas 3-in-1 machines have 7/16" T-slots), you will need T-slot nuts (see part # 35-105) to mount the vise to your table. The vise alignment feet are cut to fit a 5/8" T-slot. To use the feet in a 7/16" T-slot, the user will need to modify the feet width.